The vertical angle below the horizontal may be reduced to 5 degrees , however, if the height of the lamp is less than 750 mm. , in the figure amend the number 002439 to read 012439 and the number 33 to read 78. FORWARD VISIBILITY OF RED LIGHTS AND REARWARD VISIBILITY OF WHITE LIGHTS. This vehicle standard applies to the design and construction of vehicles as set out in the table below. The presence, number, colour, arrangement and, where applicable, the category of lamps shall be checked by visual inspection of the lamps and their markings. Aggregate maximum intensity of the driving beam headlamps which can be switched on simultaneously shall not exceed 225,000 cd. ); 5.15. 8. A second mirror must be fitted to the left hand side of any motorcycle or moped manufactured on or after July 1975. 53 in its original form. May not be combined with any other lamp. 0000006099 00000 n The aggregate maximum intensity of the driving beam headlamp(s) shall be such that the requirement in paragraph 6.1.9. of this Regulation is fulfilled. 7.4.5. 6.1.3.1.3. two driving lamps of which either one or both are reciprocally incorporated with another front lamp must be fitted in such a way that their reference centres are symmetrical in relation to the median longitudinal plane of the vehicle. Its first two digits (at present 01 for the Regulation in its 01 series of amendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. 0.1.2. In the absence of specific instructions, the electrical connection shall be such that the driving beam headlamp, the passing beam headlamp and the fog lamp cannot be switched on unless the lamps referred to in paragraph 5.10. above are likewise switched on. We pay respect to traditional custodians and Elders past and present. =lv+c/~g_G!Hz}GC(G,Ti vk In any case, the distance between the edge of the illumination surface of any independent driving lamp and the edge of that of the passing lamp must not exceed 200mm. 10. 51 0 obj <> endobj Front indicators: Two front indicators (category 1 as specified in Regulation No. Other requirements, 7.3. Vehicles must comply with the requirements of this rule. Compiled by: Vehicle Safety Standards, Department of Infrastructure and Regional Development. Direction indicators: yes/no 2/, 9.7. As a result of the trial we will introduce a new law that will permit fully licenced motorcyclists to legally filter past stationary vehicles at intersections when it is safe to do so. stop lamp means the lamp used to indicate to other road-users to the rear of the vehicle that its driver is applying the service brake; 2.5.10. The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2), with the following requirements: 8.1. 0000001558 00000 n Operating tell-tale means a visual or auditory signal (or any equivalent signal) indicating that a device has been switched on and whether or not it is operating correctly; 2.17. Position. In the case of vehicles first registered more than four years after the date of entry into force mentioned in paragraph 11.1. above. 5.18. Manoeuvre only allowed by experienced riders who may have more highly developed hazard perception and motorcycle handling skills. This Standard is the Vehicle Standard (Australian Design Rule 19/01 - Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007. Roadworthiness | NSW Government 7.2.5. 71 0 obj <>stream 6.11.3.1. in height: not less than 250 mm nor more than 900 mm above the ground; 6.11.3.2. in length at the rear of the vehicle. May be reciprocally incorporated with other front lamps other than direction indicator lamps. The Parties to the 1958 Agreement which apply this Regulation shall communicate to the United Nations secretariat the names and addresses of the technical services responsible for conducting approval tests and of the administrative departments which grant approval and to which forms certifying approval, extension or refusal or withdrawal of approval, issued, in other countries, are to be sent. Rear reflex reflectors, non-triangular: yes/no 2/. leaving a kerb. This Standard may also be cited as Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles. Venue Closure for State Title Hosts. Vehicle Standard (Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007 (F2007L01429), Vehicle Standard (Australian Design Rule 19/01 Requirements for Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007 Amendment 1 (F2016L00531). or the light-emitting surface (c-d), in a plane perpendicular to the direction of observation and tangential to the most exterior point of the lens (see annex 3 to this Regulation); 2.9. These segments are determined in relation to the axis of reference. FRONT REFLEX REFLECTOR, NON-TRIANGULAR, 7.4.1. 0000002815 00000 n In the scale of shit that matters, this sits very low. Anyway, the bike was a one-off in Australia - no more have ever been officially imported. May be grouped with other front lamps. Motorcycle and scooter riders | NSW Government REAR POSITION LAMP, 8.5.1. REQUIREMENTS. May be combined with any other front lamps. Position. equivalent lamps means lamps having the same function and authorised in the country in which the vehicle is registered; such lamps may have different characteristics from those of the lamps with which the vehicle is equipped at the time of approval, on condition that they satisfy the requirements of this Regulation; 2.5.2. Application for approval, 6. east Lane filtering Know when lane filtering is legal and illegal. 6.7.6. The values measured for the angles shall be such that the individual specifications applicable to each lamp are fulfilled except that the limits of the angles may have an allowance corresponding to the +/- 3 degrees variation permitted in paragraph 5.3. for the mounting of the light-signalling devices. This Standard may also be cited as Australian Design Rule 19/01 - Installation of Lighting and Light-Signalling Devices on L-Group Vehicles. The electrical connections shall be such that the front position lamp or the passing beam headlamp, if there is no front position lamp, the rear position lamp and the rear registration-plate illuminating device cannot be switched on or off otherwise than simultaneously. Defined by angles alpha and beta as specified in paragraph 2.11.: beta = 45 degrees to left and to right for a single lamp, except for an off-centre light, in which case the inward angle beta = 10 degrees ; beta = 45 degrees outwards and 10 degrees inwards for each pair of lamps. <<97514530CE571148B85A3E44D896D4AC>]/Prev 23980>> Technical specifications for buses. May not be reciprocally incorporated with any other lamp. I have to believe that with the brighter lights on newer bikes, we will see increased effectiveness from daytime running lights. Refer to paragraph 2 of Appendix A. Number, 7.3.2. 2.12.3. of front and rear position lamps and retro-reflectors; 2.13. direction-indicator lamp means the lamp used to indicate to other road-users that the driver intends to change direction to the right or to the left; A direction-indicator lamp or lamps may also be used according to provisions of Regulation No. 2.5.9. Reason(s) for extension (if applicable):.. 13. This Standard also repeals each instrument made under section 7 of the Motor Vehicle Standards Act 1989 that creates a vehicle standard with the name Australian Design Rule 14/02 Rear Vision Mirrors, if there are no other vehicle standards created by that instrument, or amendments to vehicle standards made by that instrument, that are still in MOT inspection manual: motorcycles - 4. Lamps, reflectors and - GOV.UK Circuit-closed tell-tale. I'd love to see this info from a primary source. 6.3.3.1. in width: For front indicators, the following requirements shall all be met: 1. there shall be a minimum distance of 240 mm between illuminating surfaces. 8.1. Vehicle Standard (Australian Design Rule 19/01 Requirements for Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007 Amendment 1. 4. 0000003403 00000 n 53 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF CATEGORY L3 VEHICLES (MOTOR CYCLES) WITH REGARD TO THE INSTALLATION OF LIGHTING AND LIGHT SIGNALLING DEVICES from the edition incorporating the 00 series of amendments up to and including the edition incorporating the 01 series of amendments are deemed to be equivalent to the technical requirements of this rule. This vehicle standard prescribes requirements for the number and mode of installation of lighting and light-signalling devices on L-group vehicles. Motorcycle Lighting Laws | Legal Beagle The competent authority issuing the extension of approval shall assign a series number for such an extension and inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in annex 1 to this Regulation. If the reflector and lens are adjustable relative to one another, the mean adjustment should be used; 2.7.2. Circuit-closed tell-tale prohibited. Non-flashing green signal lamp. 8.9.5. 1.2.2. Rear-registration-plate illuminating device: yes/no 2/. The front direction indicators may move in line with the steering angle. One. On the inside of the angles of geometric visibility no account is taken of obstacles, if they were already presented when the lamp was type-approved. 5.5.2.4. have identical nominal photometric characteristics; 5.5.2.5. come on and go off simultaneously; 5.6. 1/ 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Yugoslavia, 11 for the United Kingdom, 12 for Austria, 13 for Luxembourg, 14 for Switzerland, 15 (vacant),16 for Norway, 17 for Finland, 18 for Denmark , 19 for Romania, 20 for Poland and 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 (vacant), 25 for Croatia, 26 for Slovenia, 27 for Slovakia, 28 for Belarus, 29 for Estonia, 30 (vacant), 31 for Bosnia and Herzegovina, 32-36 (vacant) and 37 for Turkey. Rear reflex reflectors, non-triangular: yes/no, 9.19. 8.9.9. 3.1. SUPPLEMENTARY GENERAL REQUIREMENTS. 8.8. Horizontal angle: 80 degrees to left and to right for a single lamp: the horizontal angle may be 80 degrees outwards and 45 degrees inwards for each pair of lamps: Vertical angle: 15 degrees above and below the horizontal. Under North Carolina law, it is illegal to sell or own a motorcycle that does not have a brake light visible from 100 feet away, unless the motorcycle was manufactured before Dec 31, 1955 . In length: at the front of the vehicle. 6.2. This Regulation applies to the approval of two-wheeled power-driven vehicles without side-car, having a maximum design speed exceeding 50 km/h and/or a cylinder capacity exceeding 50 cm3. The colour of light emitted by lamps referred to in this national standard must be as specified in Table 1, Rear registration plate illuminating device, 7. The above approval mark affixed to a motor cycle shows that the vehicle type concerned has been approved in the Netherlands (E4) pursuant to Regulations Nos. Originally posted by F2005L04012 For rear indicators, the clearance between the inner edges of the two illuminating surfaces shall be at least 180 mm 2. 0.1.2. If there is a front fog lamp, it shall be possible to switch off the rear fog lamp independently of the front fog lamp. In width: For LD category vehicles, at least one reflector must be mounted on the motor cycle as per paragraph 6.8.3 of Appendix A. EXEMPTIONS AND ALTERNATIVE PROCEDURES. Filtering at high speeds is dangerous and will increase the crash risk for motorcycle riders and other roads users, particularly cyclists and pedestrians. Front position (side) lamps: yes/no, 9.12. rear fog lamp means the lamp used to make the vehicle more easily visible from the rear in dense fog; 2.6. VEHICLE-HAZARD WARNING SIGNAL. NARVA stock a wide range of additional lighting, including L.E.D driving lights and light bars, plus work lamps suitable for a variety of applications and legal fitment. 0000000016 00000 n 6.2.2. distance between two lamps which face in the same direction means the shortest distance between the two apparent surfaces in the direction of the reference axis. Circuit-closed tell-tale. 6.10.6. Apparent surface based on light-emitting surface. 6.12.3.1. on the side of the vehicle. 6.3. The lamps may move with the steering. That field of the solid angle is determined by the segments of the sphere of which the centre coincides with the centre of reference of the lamp and the equator is parallel with the ground. Reversing Lamp (clause 7.2) applicable to LA and LC category vehicles only if fitted with reverse gear. 0000005361 00000 n The Table of Amendments provides a history of clauses that have been amended, inserted or deleted. May reduce risk of inexperienced riders having crashes associated with inadequate gap selection or awareness of pedestrians/other road users while filtering. 0000003648 00000 n 0.2.1. The key road rules and reference numbers regarding motorcycles are: 146 - Driving within a single marked lane or line of traffic 151 - Riding a motor bike or bicycle alongside more than 1 other rider 151A and B - Lane filtering 156 - Transit lanes 197 - Stopping on a path, dividing strip or nature strip 270 - Wearing motor bike helmets 53. Check your lights are working, including headlights, brake lights and indicators. 2, 2. 3.1. The following individual requirements are additional to the requirements set out in Appendix A. LAMP SURFACES, AXIS AND CENTRE OF REFERENCE, AND ANGLES OF GEOMETRIC VISIBILITY, 6. Parking Lamp (clause 7.1), 6.3.5. This requirement shall be deemed to be satisfied if the light emitted does not cause discomfort to the driver either directly, or indirectly through the rear-view mirrors and/or other reflecting surfaces of the vehicle. Illuminating surface of a light-signalling device other than a retro-reflector (paragraphs 2.5.8., 2.5.9., 2.5.11., 2.5.12., 2.5.14. and 2.5.16.) For LA category vehicles: The technical requirements of any of the editions of United Nations Economic Commission for Europe Regulation No. Other requirements. Family Licence Discount. centre of reference means the intersection of the axis of reference with the exterior light-emitting surface; it is specified by the manufacturer of the lamp; 2.11. Where the fitment of a lamp is indicated as optional, this means that it is not mandatory to fit the lamp but, if fitted, the lamp(s) are required to comply. The front side retro-reflectors may move with the steering angle. 74 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF MOPEDS WITH REGARD TO THE INSTALLATION OF LIGHTING AND LIGHT SIGNALLING DEVICES from the edition incorporating the 00 series of amendments up to and including the edition incorporating the 01 series of amendments are deemed to be equivalent to the technical requirements of this rule. This compilation of Vehicle Standard (Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007 includes all the instruments set out in the Table of Instruments. For the purposes of determining the lower, upper and lateral edges of the device, only horizontal and vertical planes shall be considered; 2.8. ). Motorcycle tyre tread depth - what you need to know The application for approval of a vehicle type with regard to the installation of its lighting and light-signalling devices shall be submitted by the vehicle manufacturer or by his duly accredited representative. Side reflex reflectors, non-triangular: yes/no 2/. The lighting and light-signalling devices shall be so fitted that in normal conditions of use, and notwithstanding the vibrations to which they may be subjected, they retain the characteristics prescribed by this Regulation and enable the vehicle to comply with the requirements of this Regulation. 2.1. SUPPLEMENTARY INDIVIDUAL SPECIFICATIONS. Vehicles certified to ADR 67/ need not comply with this rule. 6.1.6. vehicle type means a category of vehicles which do not differ from each other in such essential respects as: 2.2.1. the dimensions and external shape of the vehicle; 2.2.2. the number and position of the devices; 2.2.3 the following shall likewise not be deemed to be vehicles of a different type: 2.2.3.1. vehicles which differ within the meaning of paragraphs 2.2.1. and 2.2.2. above but not in such a way as to entail a change in the kind, number, position and geometric visibility of the lamps prescribed for the vehicle type in question; and. Setting at 30km/h will limit filtering to slow moving traffic where vehicles are moving at or below this speed, This speed is 10km/h lower than the 40km/h limit currently implemented in high pedestrian activity zones, Limit filtering to fully licenced riders only (excluding Learner or Provisional riders). This pre-determined reference value shall be indicated on a plate on each vehicle. Mandatory. 9.19. Limitations on the number of open events permitted to be conducted. 4, 6. You can email them at vehiclestandards@nhvr.gov.au launch or call them on 1300 696 487. Headlamp, position lamps, stop lamps, direction indicators, rear registration plate lamp, rear reflector and direction indicator 'tell-tale' rules and inspection for motorcycle MOT tests.. 2.4. hazard warning signal means the simultaneous operation of all of a vehicles direction- indicator lamps to show that the vehicle temporarily constitutes a special danger to other road users; 2.5.15. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement concerning the Recognition of Approval for Motor Vehicle Equipment and Parts, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations. front fog lamp means the lamp used to improve the illumination of the road in case of fog, snowfall, rainstorms or dust clouds; 2.5.16. 6.10.3.1. in width: for a single lamp the centre of reference shall be in the median longitudinal plane of the vehicle; or the edge of the illuminating surface which is nearest to that plane shall be not more than 250 mm away from it; 6.10.3.2. in height: not less than 250 mm above the ground. The electrical connections shall be checked by switching on every lamp supplied by the electrical system of the motorcycle. 53, as amended by the 01 series of amendments. Vehicle Standard (Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007, Road Vehicle Standards (Consequential and Transitional Provisions) Act 2018, Vehicle Standard (Australian Design Rule 19/01 Requirements for Installation of Lighting and Light Signalling Devices on L-Group Vehicles) 2007 Amendment 1 - F2016L00531. Riders will be able to filter at a speed limit of 30km/h. For LD category vehicles, the front position lamp and the rear position lamp on the side-car may be combined provided that the geometric visibility for each lamp is maintained. It may not display this or other websites correctly. Horizontal angles beta = 30 degrees to the front and to the rear. (1) A motor vehicle with 4 or more wheels, and a trailer, must have a rear-facing red reflector towards each side of its rear. Helmet laws address safety helmet use by motorcycle, low-power cycle (moped, scooter, motorized cycle), or bicycle riders. Annex 2 to this Regulation gives examples of the arrangement of the approval marks. As from 24 months after the date of entry into force mentioned in paragraph 11.1 above, Contracting Parties applying this Regulation shall grant approvals only if the vehicle type with regard to the number and mode of installation of the lighting and light- signalling devices corresponds to the requirements of the 01 series of amendments to this Regulation. Trading Hours. (2) A motor bike, a sidecar attached to a motor bike, and a motor trike, must have a rear-facing red reflector. NSW - Rule change for indicators | Netrider - Connecting Riders! The following provisions of Appendix A do not apply to this rule: Section 7 - Modifications of the vehicle type or of the installation of its lighting and light signalling devices, Section 9 - Penalties for non-conformity of production, Section 10 - Production definitely discontinued, Section 12 - Names and addresses of technical services responsible for conducting approval tests, and of administrative departments. REVERSING LAMP, 7.2.1. However, the dangerous practice of filtering over the speed limit of 30km/h will become its own specific offence. Rear position (side) lamps: yes/no, 9.16. The vertical angle below the horizontal may be reduced to 5 degrees , however, if the height of the lamp is less than 750 mm. Where the fitment of a lamp is indicated as optional, this means that it is not mandatory to fit the lamp but, if fitted, the lamp(s) are required to comply. This Standard commences on the day after it is registered. 14. Minor Modifications publication (PDF, 414 KB). 8.9.10. 6.3.10.4. Strengthen Helmet Laws | US Department of Transportation NOTES, 10.1. 6.9.1. The department may then either; 7.1.1. consider that the modification made are unlikely to have appreciable adverse effects and that in any case the vehicle still complies with the requirements; or, 7.1.2. require a further test report from the technical service responsible for conducting tests. 6.12.3.2. in height: not less than 300 mm nor more than 900 mm above the ground; 6.12.3.3. in length: should be placed in such a position that under normal conditions it may not be masked by the drivers or passengers clothes. Discussion, Rides/Events Calendar, Showcases, Reviews, Classifieds, Blogs, and Resources. 1. The list of documents deposited with the Administrative Service which has granted the approval is annexed to this communication and may be obtained upon request. Model A of the approval mark, in the figure amend the number 002439 to read 012439 and in the caption below the figure, the words Regulation No. (The initial downward inclination of the cut-off of the passing beam shall be checked against the requirements of paragraph 6.2.5.). Orientation Forward. 0000000716 00000 n The vertical angle below the horizontal may be reduced to 5o, if the height of the lamp is less than 750 mm, 7.1.5. Motorcycle Daytime Running Lights: Everything You Should Know unladen vehicle means a vehicle without a driver, or passenger, and unladen, but with its fuel tank full and its normal complement of tools; 2.5. It clearly states that a rear reflector is mandatory: "A motor bike, a sidecar attached to a motor bike, and a motor trike, must have a rear-facing red reflector" (Division 16, cf ALVSR 2015 r 105; 2007 reg Sch 2 cl 118). Orientation Forward. May be combined with any other front lamps. Notice of approval or of refusal of approval or production definitely discontinued of a vehicle type/part pursuant to this Regulation shall be communicated to the Parties to the Agreement which apply this Regulation, by means of a form conforming to the model in annex 1 to this Regulation. The reference orientation corresponding to the vehicle plus driver shall be set between - 1 % and - 1.5 %. 10. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement concerning the Recognition of Approval for Motor Vehicle Equipment and Parts, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations. Conformity of production, 9. Tell-tale No requirement. This tell-tale shall not be required if the instrument illumination lighting can be switched on or off only simultaneously with the position lamp(s). 7.2.7. 0000002948 00000 n 5.5. The conspicuity lamps shall be lighted each time the engine is started but may be extinguished whenever a passing lamp or driving lamp to Appendix A of this rule is lighted. Alternative requirements A single or twin passing lamp(s) to paragraph 6.2. of Appendix A shall be deemed to meet the requirements for conspicuity lamps provided that the passing lamp(s) meets the requirements of Clause 8.9.9. Contact the National Heavy Vehicle Regulator launch for heavy vehicle standards and vehicle standards guides (VSG). 97. Orientation, 7.2.6. Mandatory. The bottom of the indicator lights must not be lower than 350mm from the ground and the top of the indicator lights must not be higher than 1200mm from the ground. (a) for a motorbike or the single wheel end of a motortrike 300mm from the centre of the other light; and. 0000002860 00000 n Step 3. 51 21 Rear position (side) lamps: yes/no 2/. 6.2.3.2. 1/ The latter is given merely as an example. Sat 8:30am - 4:00pm. 12months rego, transfer and stamp duty was $443. 0000001268 00000 n The control for changing over to the passing beam(s) shall switch off the driving beam(s) simultaneously. Lighting and light-signalling devices type-approved for four-wheeled vehicles of categories M1 and N1 and referred to in sections 5.14. and 5.15. may also be fitted to motorcycles. 5.12.2. 6.1.3.1.2. a driving lamp that is reciprocally incorporated with another front lamp must be fitted in such a way that its reference centre lies within the median longitudinal plane of the vehicle; however, when the vehicle is also fitted with an independent passing lamp alongside the driving lamp their reference centres must be symmetrical in relation to the median longitudinal plan of the vehicle. It is important to note the new law will not apply to school zones during hours of operation where there might be an increase in pedestrian activity. In the absence of specific instructions, the height and orientation of the lamps shall be verified with the vehicle unladen and placed on a flat horizontal surface, its median longitudinal plane being vertical and the handlebars being in the position corresponding to the straight ahead movement. What are the rules in our other states ,please? The conspicuity lamps need not be lighted whenever the engine is not operating or when the device which controls the starting and stopping of the engine is in the off position. Horizontal angle: from 30o left to 30o right. No red light shall be visible towards the front and no white light shall be visible towards the rear. 5.9. How to register a bike in NSW - braaap Motorcycles You must signal your intention with your direction indicators to: move to the left or right turn left or right. PASSING LAMP, 8.2.1. It shall be accompanied by the undermentioned documents in triplicate and the following particulars: 3.2.1. a description of the vehicle type with regard to the items mentioned in paragraphs 2.2.1. to 2.2.3. above; the vehicle type duly identified shall be specified; 3.2.2. a list of the devices intended by the manufacturer to form the lighting and light-signalling equipment; the list may include several types of device for each function; each type shall be duly identified (national or international approval mark, if approved, name of manufacturer, etc. Make an appointment. 8.9.8. 9.8. 74 UNIFORM PROVISIONS CONCERNING THE APPROVAL OF MOPEDS WITH REGARD TO THE INSTALLATION OF LIGHTING AND LIGHT SIGNALLING DEVICES from the edition incorporating the 00 series of amendments up to and including the edition incorporating the 01 series of amendments are deemed to be equivalent to the technical requirements of this rule. startxref The device may consist of several optical components designed to illuminate the space reserved for the registration plate. The information provided by us is correct as of May 2020. Filtering only permitted when it is safe to do so. However, a majority of states only require use of a helmet up to a certain age, varying from age 17 to 20 years, or have .

Sunderland Council Pest Control Contact Number, Atlanta Mad Hatters Hockey 14u, Motorcycle Racing School Las Vegas, Melbourne Food And Wine Festival 2022 Dates, Retriev Technologies Inc Stock, Articles M